Chemical Engineering / Kimya Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/14

Browse

Now showing 1 - 20 of 162

Citation - WoS: 21
Citation - Scopus: 23
Activated Carbon Adsorption of Fuel Oxygenates Mtbe and Etbe From Water
(Springer Verlag, 2009-11) İnal, Fikret; Yetgin, Senem; Aksu, Gülsüm T.; Şimşek, Selvi; Sofuoğlu, Aysun; Sofuoğlu, Sait Cemil
The aqueous phase adsorption of fuel oxygenates methyl tertiary butyl ether (MTBE) and ethyl tertiary butyl ether (ETBE) onto commercially available granular activated carbon (GAC; Norit GAC 1240) was investigated in a batch system at 27°C. The oxygenate concentrations were determined by headspace gas chromatography/mass spectrometry analyses. The experimental data were used with four two-parameter isotherm models (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and two kinetic models (pseudo first-order and pseudo second-order) to determine equilibrium and kinetic parameters. Considering the correlation coefficient and root mean square error, Dubinin-Radushkevich isotherm showed better fit with the equilibrium data for MTBE. However, the performances of Langmuir and Dubinin-Radushkevich models were comparable for ETBE. The adsorption capacities were calculated as 5.50 and 6.92 mg/g for MTBE and ETBE, respectively, at an equilibrium solution concentration of 1 mg/L using Dubinin-Radushkevich isotherm. The differences between the model predictions and experimental data were similar for the pseudo first-order and pseudo second-order kinetic models. Gibbs free-energy changes of adsorption were found to be -22.59 and -28.55 kJ/mol for MTBE-GAC and ETBE-GAC systems, respectively, under the experimental conditions studied.
Citation - WoS: 3
Citation - Scopus: 5
Adsorption Characteristics of Lead-, Barium- and Hydrogen-Rich Clinoptilolite Mineral
(SAGE Publications Inc., 2003) Çakıcıoğlu Özkan, Seher Fehime; Ülkü, Semra
The carbon dioxide and water vapour adsorption properties of local clinoptilolite-rich material, both as the original and as lead-, barium- and hydrogen-rich forms, were examined. The lead- and barium-rich forms were prepared by treatment of the original clinoptilolite with Pb(NO3)2 and BaCl2 respectively, while the hydrogen-rich form was prepared by NH4Cl and heat treatment. Water and CO2 adsorption experiments were conducted in a volumetric system under static conditions, with low-pressure adsorption data being used for the characterization of the natural, Pb-rich, Ba-rich and H-rich clinoptilolite samples. Although the existence of barium-exchange was not noted, an appreciable decrease in CO2 adsorption was observed with the Pb-rich and H-rich forms due to a decrease in the electrostatic interaction between the surface and the adsorbate. Application of the Dubinin-Astakhov equation to the water adsorption data established the existence of micropores of different sizes that exhibited different adsorption mechanisms.
Citation - WoS: 21
Citation - Scopus: 23
Adsorption of Anionic Polyelectrolyte and Comb Polymers Onto Lead Magnesium Niobate
(Elsevier Ltd., 2008-03) Şakar-Deliormanlı, Aylin; Çelik, Erdal; Polat, Mehmet
This paper presents the results concerning the adsorption mechanism of polyacrylic acid (PAA) and polyacrylic acid/polyethylene oxide (PAA/PEO) comb polymer onto lead magnesium niobate (PMN) powders. In the study adsorption behavior of PAA and PAA/PEO onto PMN surface were determined in aqueous solutions and the influence of pH and ionic strength was investigated. Results showed that adsorption of PAA or PAA/PEO increased with decreasing pH of the suspensions. The increase in the ionic strength or the presence of divalent cations caused an increase in the adsorption of both polyelectrolytes. It was observed that the adsorption reaches a maximum when PAA is fully complexed in solution. On the other hand, the increase in the adsorption of PAA/PEO onto PMN in the presence of monovalent or divalent salt was attributed to the decrease in the electrostatic forces rather than complex formation with the divalent metal ions in solution. Turbidity measurements showed that there is no complex formation between the divalent metal ions and PAA/PEO comb polymers due to shielding effect of the PEO teeth.
Citation - WoS: 67
Citation - Scopus: 75
Air-Water Exchange of Polychlorinated Biphenyls (pcbs) and Organochlorine Pesticides (ocps) at a Coastal Site in Izmir Bay, Turkey
(Elsevier Ltd., 2008-02) Odabaşı, Mustafa; Çetin, Banu; Demircioğlu, Eylem; Sofuoğlu, Aysun
The air-water exchange of polychlorinated biphenyl (PCB) and organochlorine pesticides (OCPs) were investigated using paired air-water samples (n = 16) collected in July and February-March, 2005 from Guzelyali Port in Izmir Bay, Turkey. Atmospheric PCBs and OCPs were mainly in gas-phase in both periods. However, their dissolved and particle-phase water concentrations were comparable. For PCBs, 3 and 4-Cl congeners were dominant while chlorpyrifos, endosulfans and HCHs were the most abundant OCPs for all samples. Especially in summer, calculated net gas-exchange PCB fluxes were mainly volatilization from the water ranging from - 0.2 (volatilization, PCB-101) to - 30.0 (volatilization, PCB-31) ng m- 2 day- 1. For OCPs, net flux ranged from - 0.03 (volatilization, cis-nonachlor) to 1568 (deposition, endosulfan I) ng m- 2 day- 1 and they have seasonal variations with generally deposition in winter and volatilization in summer. However, endosulfan I, II, endosulfan sulfate, α- and γ-HCH deposited in both periods. The calculated residence times of PCBs and OCPs in the water column indicated that the gas-exchange in the Bay is at least as or a more important mechanism than advection. Annual gaseous absorption and volatilization fluxes were calculated and were used along with the estimated dry deposition fluxes and wet deposition fluxes measured recently at a suburban site in Izmir to determine the relative contributions of different atmospheric mechanisms to the pollutant inventory of the Bay water column. Results suggested that the relative contributions of all studied mechanisms to the water column PCB and OCP inventories were significant.
Citation - WoS: 38
Citation - Scopus: 45
Alpha-Pinene Isomerization on Acid-Treated Clays
(Elsevier Ltd., 2002-01) Beşün, Nurgün; Özkan, Fehime; Gündüz, Gönül
Liquid phase isomerization of α-pinene was studied over a number of differently pre-treated montmorillonite clays. The effects of the acid pre-treatment parameters (acid-to-clay ratio (A/C), water-to-acid ratio (W/A), temperature and pre-treatment time) on the product distribution were investigated. It was observed that the pre-treatment with acid improved the catalytic activity of that catalyst which was activated at 200 °C for 4 h at A/C ratios between 0.2 and 0.4. Alpha-pinene consumption was very small over the catalysts prepared with an A/C ratio of 0.8. Characterization studies that were done by nitrogen and water vapor adsorption experiments and by IR measurements showed that catalysts with high differential pore volumes for pores around 2 nm and homogenous mesopore distributions and with low dealumination degrees were good catalysts for the production of camphene. Catalysts having heterogeneous mesoporosity were found to be the preferable ones for limonene production.
Citation - WoS: 10
Citation - Scopus: 12
Analysis of Dilution Induced Disintegration of Micellar Drug Carriers in the Presence of Inter and Intra Micellar Species
(Elsevier, 2020) Polat, Hürriyet; Kutluay, Gülistan; Polat, Mehmet
Micelles of self-assembling polymeric surfactant molecules are promising nanoscopic carriers for lipophilic and toxic drugs, genes, and imaging molecules. Though it is a must for successful transport, ensuring micelle integrity is a challenge during intravenous injection where micelles must endure abrupt dilutional effects and encounters with native molecules. Therefore, direct observational evidence of how micelles behave during dilution is valuable in manipulating the designs of these carriers for a succesful drug delivery. Morphology and stability of the barren and a drug-loaded (lipophilic probucol) micelles of a polymeric surfactant (Pluronic® P123) were monitored during systematic re-dilution in distilled water and simulated body fluid in the presence of a model protein (bovine serum albumin). It was observed through surface tension, dynamic light scattering, laser velocimetry, transmission scanning and transmission electron microscopy, and atomic force microscopy analyses that the micelles disintegrated to various degrees in all cases upon dilution. The results indicate that dilution effects must be taken into account in designing micellar drug carriers. The assistance of some other means of protection such as encapsulation should be considered for ensuring micelle integrity within the bloodstream. © 2020 Elsevier B.V.
Citation - WoS: 13
Citation - Scopus: 15
Ancillary Effects of Surfactants on Filtration of Low Molecular Weight Contaminants Through Cellulose Nitrate Membrane Filters
(Elsevier Ltd., 2016-03-05) Olcay, Aybike Nil; Polat, Mehmet; Polat, Hürriyet
Removal of contaminants with low molecular weight (<800 Dalton) requires the use of advanced separation techniques such as ultrafiltration (UF) or micellar enhanced ultrafiltration (MEUF). However, surface active agents invariably co-exist in waste waters along with these contaminants or they may be added intentionally as part of the separation process as in the case of MEUF. Though it is quite likely that both the filter medium and the contaminants would interact with the surfactant molecules or their micelles, there is not sufficient emphasis in the literature on the concomitant aspects of such interactions.The ancillary effects created by anionic (sodium dodecyl sulfate, SDS), cationic (hexadecyltrimethyl ammonium bromide, CTAB) and non-ionic (ethoxylated octylphenol, TX-100) surfactants on the mechanism and efficiency of the filtration process were investigated in this study. Methylene blue (MB) and cellulose nitrate membrane (CNM) filters were employed as model retentate and the separation medium. A combination of surface tension, contact angle and charge measurements demonstrated that the addition of surfactants had a remarkable effect on the filtration outcome. The effect depended on both the type and concentration of the surfactant and was manifested mainly through the creation of MB-surfactant entities which acted differently than the MB alone; but more importantly, through the interactions of the surfactant molecules/micelles and the MB-surfactant pairs with the separation membrane.
Citation - WoS: 24
Citation - Scopus: 29
Antibacterial Properties of Silk Fibroin/Chitosan Blend Films Loaded With Plant Extract
(Korean Fiber Society, 2010-03) Başal, Güldemet; Altıok, Duygu; Bayraktar, Oğuz
The silk fibroin (SF)/chitosan (CHI) blend films were prepared by dissolving them in formic acid. The morphology of the films was examined by scanning electron microscopy (SEM). The roughness of the membranes was determined by atomic force microscopy (AFM). These films were treated with the extracts of Pistacia terebinthus, Pistacia lentiscus, and Hypericum empetrifolium. Folin-Ciocalteu assay was used to determine the amount of total phenols adsorbed on these blend films. The antibacterial properties of films were tested using disc diffusion and turbidity measurement methods against Escherichia coli and Staphylococcus epidermidis. The release of adsorbed phenolics from the film surface resulted in antibacterial properties. © The Korean Fiber Society and Springer Netherlands 2010.
Antioxidant, Antimicrobial and Cytotoxic Activities of Some Turkish Plant Extracts
(John Wiley and Sons Inc., 2006) Altıok, Evren; Asbagh, L. Abbasi; Bulut, Çisem; Ülkü, Semra; Bayraktar, Oğuz
Plant extracts have been known to possess notable biological activity, including antioxidant, antimicrobial and cytotoxic properties. There is a growing interest in the use of natural products in the human food industries as consumer resistance to synthetic additives increases. These products can be used to improve human health. In vitro antioxidant, antimicrobial and cytotoxic activities of ethanol extracts of some plants from Urla region in Turkey were investigated. Plant materials were collected from Pistacia lentiscus, Vitex agnus-castus, Cistus creticus and Nerium oleander in October, November and December.
Citation - WoS: 18
Citation - Scopus: 22
Application of Inverse Gas Chromatography To the Measurement of Diffusion and Phase Equilibria in Polyacrylate-Solvent Systems
(Elsevier Ltd., 1999) Tıhmınlıoğlu, Funda; Danner, Ronald P.
The inverse gas chromatography technique (IGC) was used to determine the partition and diffusion coefficients of ethyl acetate and 2-ethylhexyl acrylate in polyacrylate for both infinite dilution and finite concentrations of solvent. Experiments were performed over a temperature range of 60 to 100°C, more than 100°C above the glass transition temperature of the polymer. The capillary column IGC model previously developed for determining partition and diffusion coefficients of infinitely dilute solvent has been modified to account for the concentration of the solvent in the polymer phase. Thermodynamic data obtained from retention theory and the modified capillary column IGC model are compared
Citation - WoS: 28
Citation - Scopus: 18
Artificial Neural Network Prediction of Tropospheric Ozone Concentrations in Istanbul, Turkey
(John Wiley and Sons Inc., 2010-10) İnal, Fikret
Tropospheric (ground-level) ozone has adverse effects on human health and environment. In this study, next day's maximum 1-h average ozone concentrations in Istanbul were predicted using multi-layer perceptron (MLP) type artificial neural networks (ANNs). Nine meteorological parameters and nine air pollutant concentrations were utilized as inputs. The total 578 datasets were divided into three groups: training, cross-validation, and testing. When all the 18 inputs were used, the best performance was obtained with a network containing one hidden layer with 24 neurons. The transfer function was hyperbolic tangent. The correlation coefficient (R), mean absolute error (MAE), root mean squared error (RMSE), and index of agreement or Willmott's Index (d2) for the testing data were 0.90, 8.78 μg/m3, 11.15μg/m3, and 0.95, respectively. Sensitivity analysis has indicated that the persistence information (current day's maximum and average ozone concentrations), NO concentration, average temperature, PM10, maximum temperature, sunshine time, wind direction, and solar radiation were the most important input parameters. The values of R, MAE, RMSE, and d2 did not change considerably for the MLP model using only these nine inputs. The performances of the MLP models were compared with those of regression models (i.e., multiple linear regression and multiple non-linear regression). It has been found that there was no significant difference between the ANN and regression modeling techniques for the forecasting of ozone concentrations in Istanbul. Tropospheric ozone has adverse effects on human health and environment. Here, the next-day's maximum 1-h average ozone concentrations in Istanbul were predicted using multi-layer perceptron type artificial neural networks (MLP-ANNs). The MLP-ANNs were compared to multiple linear and multiple non-linear regression models. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Citation - WoS: 24
Citation - Scopus: 25
Atmospheric Concentrations and Phase Partitioning of Polycyclic Aromatic Hydrocarbons in Izmir, Turkey
(John Wiley and Sons Inc., 2011-04) Demircioğlu, Eylem; Sofuoğlu, Aysun; Odabaşı, Mustafa
Ambient air polycyclic aromatic hydrocarbon (PAH) samples were collected at a suburban (n=63) and at an urban site (n=14) in Izmir, Turkey. Average gas-phase total PAH (∑ 14PAH) concentrations were 23.5ngm -3 for suburban and 109.7ngm -3 for urban sites while average particle-phase total PAH concentrations were 12.3 and 34.5ngm -3 for suburban and urban sites, respectively. Higher ambient PAH concentrations were measured in the gas-phase and ∑ 14PAH concentrations were dominated by lower molecular weight PAHs. Multiple linear regression analysis indicated that the meteorological parameters were effective on ambient PAH concentrations. Emission sources of particle-phase PAHs were investigated using a diagnostic plot of fluorene (FLN)/(fluorine+pyrene; PY) versus indeno[1,2,3-cd]PY/(indeno[1,2,3-cd]PY+benzo[g,h,i]perylene) and several diagnostic ratios. These approaches have indicated that traffic emissions (petroleum combustion) were the dominant PAH sources at both sites for summer and winter seasons. Experimental gas-particle partition coefficients (K P) were compared to the predictions of octanol-air (K OA) and soot-air (K SA) partition coefficient models. The correlations between experimental and modeled K P values were significant (r 2=0.79 and 0.94 for suburban and urban sites, respectively, p<0.01). Octanol-based absorptive partitioning model predicted lower partition coefficients especially for relatively volatile PAHs. However, overall there was a relatively good agreement between the measured K P and soot-based model predictions. Ambient air polycyclic aromatic hydrocarbon (PAH) samples were collected at a suburban and at an urban site in Izmir, Turkey. The multiple linear regression analysis indicated that the meteorological parameters were effective on the measured ambient PAH concentrations. The results indicated that traffic emissions were the dominant PAH sources at both sites for summer and winter seasons.
Citation - WoS: 3
Citation - Scopus: 3
Atomic-Scale Insights Into Carbon Dioxide Hydrogenation Over Bimetallic Iron-Cobalt Catalysts: a Density Functional Theory Study
(MDPI, 2023) Tuncer, Dilan; Kızılkaya, Ali Can
The conversion of carbon dioxide to fuels and chemicals is a promising long-term approach for mitigating CO2 emissions. Despite extensive experimental efforts, a fundamental understanding of the bimetallic catalytic structures that selectively produce the desired products is still lacking. Here, we report on a computational surface science approach into the effect of the Fe doping of Co(111) surfaces in relation to CO2 hydrogenation to C1 products. Our results indicate that Fe doping increases the binding strength of surface species but slightly decreases the overall catalytic activity due to an increase in the rate-limiting step of CO dissociation. FeCo(111) surfaces hinder hydrogenation reactions due to lower H coverages and higher activation energies. These effects are linked to the Lewis basic character of the Fe atoms in FeCo(111), leading to an increased charge on the adsorbates. The main effect of Fe doping is identified as the inhibition of oxygen removal from cobalt surfaces, which can be expected to lead to the formation of oxidic phases on bimetallic FeCo catalysts. Overall, our study provides comprehensive mechanistic insights related to the effect of Fe doping on the catalytic behavior and structural evolution of FeCo bimetallic catalysts, which can contribute to the rational design of bimetallic catalysts.
Citation - WoS: 2
Citation - Scopus: 3
Automated Deep Learning Model Development Based on Weight Sensitivity and Model Selection Statistics
(Pergamon-elsevier Science Ltd, 2025) Yalcin, Damla; Deliismail, Ozgun; Tuncer, Basak; Boy, Onur Can; Bayar, Ibrahim; Kayar, Gizem; Sildir, Hasan
Current sustainable production and consumption processes call for technological integration with the realm of computational modeling especially in the form of sophisticated data-driven architectures. Advanced mathematical formulations are essential for deep learning approach to account for revealing patterns under nonlinear and complex interactions to enable better prediction capabilities for subsequent optimization and control tasks. Bayesian Information Criterion and Akaike Information Criterion are introduced as additional constraints to a mixed-integer training problem which employs a parameter sensitivity related objective function, unlike traditional methods which minimize the training error under fixed architecture. The resulting comprehensive optimization formulation is flexible as a simultaneous approach is introduced through algorithmic differentiation to benefit from advanced solvers to handle computational challenges and theoretical issues. Proposed formulation delivers 40% reduction, in architecture with high accuracy. The performance of the approach is compared to fully connected traditional methods on two different case studies from large scale chemical plants.
Citation - WoS: 18
Citation - Scopus: 21
Bioactive Snail Mucus-Slime Extract Loaded Chitosan Scaffolds for Hard Tissue Regeneration: the Effect of Mucoadhesive and Antibacterial Extracts on Physical Characteristics and Bioactivity of Chitosan Matrix
(IOP Publishing, 2021) Perpelek, Merve; Tamburacı, Sedef; Aydemir, Selma; Tıhmınlıoğlu, Funda; Baykara, Başak; Karakaşlı, Ahmet; Havıtçıoğlu, Hasan
Biobased extracts comprise various bioactive components and they are widely used in tissue engineering applications to increase bioactivity as well as physical characteristics of biomaterials. Among animal sources, garden snail Helix aspersa has come into prominence with its antibacterial and regenerative extracts and show potential in tissue regeneration. Thus, in this study, bioactive H. aspersa extracts (slime, mucus) were loaded in chitosan (CHI) matrix to fabricate porous scaffolds for hard tissue regeneration. Physical, chemical properties, antimicrobial activity was determined as well as in vitro bioactivity for bone and cartilage regeneration. Mucus and slime incorporation enhanced mechanical properties and biodegradation rate of CHI matrix. Scanning electron microscopy images showed that the average pore size of the scaffolds decreased with higher extract content. Mucus and slime extracts showed antimicrobial effect on two bacterial strains. In vitro cytotoxicity, osteogenic and chondrogenic activity of the scaffolds were evaluated with Saos-2 and SW1353 cell lines in terms of Alkaline phosphatase activity, biomineralization, GAG, COMP and hydroxyproline content. Cell viability results showed that extracts had a proliferative effect on Saos-2 and SW1353 cells when compared to the control group. Mucus and slime extract loading increased osteogenic and chondrogenic activity. Thus, the bioactive extract loaded CHI scaffolds showed potential for bone and cartilage regeneration with enhanced physical properties and in vitro bioactivity.
Citation - WoS: 28
Citation - Scopus: 36
Bioleaching of Nickel From Equilibrium Fluid Catalytic Cracking Catalysts
(Springer Verlag, 2005-07) Bayraktar, Oğuz
This study investigates the possibility of reusing metal-contaminated equilibrium fluid catalytic cracking (FCC) catalyst after bioleaching. Leaching with Aspergillus niger culture was found to be more effective in the mobilization of nickel from the catalyst particles compared to chemical leaching with citric acid. Bioleaching achieved 32% nickel removal whereas chemical leaching achieved only 21% nickel removal from catalyst particles. The enhanced nickel removal from the catalysts in the presence of A. niger culture was attributed to the biosorption ability of the fungal mycelium and to the higher local concentration of citric acid on the catalyst surface. It was found that 9% of solubilized nickel in the liquid medium was biosorbed to fungal biomass. After nickel leaching with A. niger culture, the hydrogen-to-methane molar ratio and coke yield, which are the measures of dehydrogenation reactions catalysed by nickel during cracking reactions, decreased significantly.
Citation - WoS: 5
Citation - Scopus: 7
Bleach-Containing Automatic Toilet-Bowl Cleaners as Sources of Vocs, Associated Indoor Air Concentrations and Carcinogenic Risk
(Turkish National Committee for Air Pollution Research (TUNCAP), 2020) Ayrı, İlknur; Genişoğlu, Mesut; Gaygısız, Handan; Sofuoğlu, Aysun; Sofuoğlu, Sait Cemil
Household cleaning products are sources of volatile organic compounds (VOCs). Bleach containing products are a special case because reactions occur between chloride and their organic content such as surfactants, perfumes, etc., generating VOCs. This study aimed to determine concentration of 13 VOCs in bleach-containing automatic toilet cleaners, to estimate their indoor air concentrations and associated exposure and health risk levels. Experiments with products purchased from supermarkets were conducted in 20-mL headspace vials by placing 1 g of sample with and without water. Solid-phase micro extraction with a DVB/CAR/PDMS fiber assembly was used for adsorption of VOCs from the headspace, and analyzed using a GC-MS. The median carbon tetrachloride and chloroform concentrations of the studied products ranged from 5.03 × 10?3 to 2.37 × 10?2 ?g/g and 2.53 × 10?2 to 2.37 ?g/g, respectively. The modeled 95th percentile indoor air concentrations in a 1.6 m3 bathroom with no ventilation were estimated to be 1 and 20 ?g/m3 for carbon tetrachloride and chloroform, respectively. The 95th percentile carcinogenic risk associated even with the use of the highest content product, 3.72 × 10?7 and 8.62 × 10?7 for carbon tetrachloride and chloroform respectively, were below the acceptable risk. In conclusion, automatic toilet-bowl cleaners were found to be sources of VOCs, but their emission potentials are not high to cause considerable indoor air concentrations over their suggested product lifetime. In turn, carcinogenic risks associated with inhalation exposure are below the de Minimis risk level of 10?6. © 2020
Citation - WoS: 10
Citation - Scopus: 11
Box-Behnken Design for Hydrogen Evolution From Sugar Industry Wastewater Using Solar-Driven Hybrid Catalysts
(American Chemical Society, 2022-11) Orak, Ceren; Yüksel, Aslı
Hydrogen is a clean and green fuel and can be produced from renewable sources via photocatalysis. Solar-driven hybrid catalysts were synthesized and characterized (scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, and UV-vis diffuse reflectance spectroscopy (DSR)), and the results implied that graphene-supported LaRuO3is a more promising photocatalyst to produce hydrogen and was used to produce hydrogen from sugar industry wastewater. To investigate the main and interaction effects of reaction parameters (pH, catalyst amount, and [H2O2]0) on the evolved hydrogen amount, the Box-Behnken experimental design model was used. The highest hydrogen evolution obtained was 6773 μmol/gcatfrom sugar industry wastewater at pH 3, 0.15 g/L GLRO, and 15 mM H2O2. Based on the Pareto chart for the evolved hydrogen amount using GLRO, among the main effects, the only effective parameter was the catalyst amount for the photocatalytic hydrogen evolution from sugar industry wastewater. In addition, the squares of pH and two-way interaction of pH and [H2O2]0were also statistically efficient over the evolved hydrogen amount.
Citation - WoS: 4
Citation - Scopus: 4
Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water
(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, Asli
In batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.
Citation - WoS: 9
Citation - Scopus: 11
Calf Thymus Dna Characterization and Its Adsorption on Different Silica Surfaces
(Royal Society of Chemistry, 2015) Yetgin, Senem; Balköse, Devrim
DNA adsorption is the initial stage of gene therapy for drug delivery systems and solid phase extraction methods of DNA purification. High pore volume and high adsorption capacity are simple requirements not only for producing 'smart' drug delivery systems but also the development of purification kits. Silica is the most used material for this purpose. The present study aimed at elucidating the calf thymus DNA biosorption process by the characterization of calf thymus DNA and silica to increase the efficiency of the currently used silica material. Mesoporous silica has long been used for DNA adsorption and silica aerogel is the new adsorbent investigated in the present study. When DNA solution was freeze dried on a silica wafer, self-assembled super helices formed as shown by atomic microscopy (AFM). Thus DNA existed not as single molecules but as large sized agglomerates in water. Thus it could be adsorbed in the macropores and on the external surface of adsorbents. Adsorption of calf thymus DNA to a silica aerogel, a mesoporous silica gel and a silica wafer was investigated in the present study. Silica aerogel was synthesized from TEOS by a supercritical ethanol drying process. The DNA adsorption capacity of the silica aerogel was nearly two times that of the mesoporous silica gel due to its macroporous structure and its higher silanol content. Silica aerogel was found to be a very promising material for DNA adsorption. Therefore silica aerogel can be considered as a good candidate for the delivery of DNA.